|
|
L421 Four Post Lift Rack
14,000 Lb. Capacity, Split-Front for Easy Service Access.
Engineered to be a Long-Term Investment.
See Flash Animation |
|
 |
|
|
Designed for operating efficiency, the Hunter L421 Four-Post Lift provides full service capability for a wide range of vehicles. The L421 combines 188-1/2” (4788 mm) general service wheelbase, 22-1/2” (572 mm) runway width and 14,000 pound (6350 kg) capacity.
|
|
The L421 Four-Post Lift features clip-on, movable work steps which make the technician's job easier. Steps allow safer access to key alignment points. |
|
Multi-service use, no floor obstructions
Floor area is clear for technician, tools and equipment.
Locks at any of 20 heights
Locks to a maximum of 70” (1778 mm) runway height. Alignment level can be set at any of the 20 lock positions; leveling legs are not needed.
Fully equipped for total four-wheel alignment
Flush-mounted, full-floating rear wheel slip plates allow the vehicle's rear suspension to be “relaxed” for maximum alignment accuracy. Built-in turnplate pockets are designed to accept a variety of available turnplates.
|
|
 |
|
All controls are in one location for ease of use.
Air connections are filtered and lubricated for long air lock, jack, and air tool life. |
|
|
|
Safety Technology
- To lower the lift, the “Latch Retract” button and the hydraulic release must be depressed at the same time. This assures that the operator is clear of the runways.
- If any vehicle exceeds lift capacity, the hydraulic bypass valve prevents lift operation.
- Pressure-compensated flow control valve assures a constant descent rate that is unaffected by the weight of the vehicle.
- Hydraulic velocity fuse monitors fluid flow rate. If the lift lowers at a higher than normal speed, the velocity fuse will stop the lift in a safe, level position.
- All hydraulic lines are covered or positioned within the steel structure to protect them from damage.
^ Back to Top
|
Specifications |
| |
L421 |
w/ Extensions |
| Max. Vehicle Gross Weight: |
14,000 lbs. (6350 kg) |
14,000 lbs. (6350 kg) |
| Max. Wheelbase: |
General Service |
188-1/2” (4788 mm) |
226-1/2” (5753 mm) |
|
Two-wheel alignment |
172-1/2” (4382 mm) |
210-1/2” (5347 mm) |
|
Four-wheel alignment |
158” (4013 mm) |
196” (4978 mm) |
| Min. 4-Wheel Alignment: |
88” (2235 mm) |
88” (2235 mm) |
| Max. Lifting Height: |
70” (1778 mm) |
70” (1778 mm) |
| Shipping Weight: |
4600 lbs. (2087 kg) |
+585 lbs (+265 kg) |
|
| Tread Width: |
Minimum width of 40” (1016 mm) between inside of tires.
Maximum width of 85” (2159 mm) to outside of tires.
|
 |
| Alignment Height: |
Any of 20 lock positions |
| Minimum Height: |
8” (203 mm) |
| Overall Height: |
93” (2362 mm) |
| Motor:
^ Back to Top |
3 h.p., 208-230 VAC, 60 Hz, 1-ph |
|
| Models |
|
| L421 |
|
Four-Post Lift, Open Front |
|
| L421–43 |
|
L421 with (2) 8,000-lb. capacity Swing Air-Jacks |
|
Two gusseted and louvered approach ramps
Two rear ramp stops
Two front wheel stops
Two wheel chocks
Two clip-on work steps with skid protection
Built-in, full-length jack rails
80” (2032 mm) rear slip plates, flush-mounted, with tethered lock pins
Built-in rub rails
Built-in turnplate pockets
Built-in air line kit
Pre-drilled for communications interface kit
Lubricator/air filter with auto-drain
|
Options |
|
| 20–1587–1 |
|
L421 Runway Extension Kit with Filler Plates |
|
| 20–593–1 |
|
Communications Interface Kit (new rack) |
|
| 20–1622–1 |
|
L421 and L424 Drive-Thru Kit* |
|
| 20–1248–1 |
|
Wear Detector Plates |
|
| 20–1365–1 |
|
Ramp Extension Kit (for low clearance vehicles) |
|
| 25–140–1 |
|
Turnplate, 14” (356 mm), (2 required)** |
|
| 25–129–1 |
|
Stainless Steel Turn Plate, 14” (356 mm), (2 required) |
|
| 46–372–1 |
|
Front Filler Plate (2 required) |
|
| 64–50–2 |
|
Jack Pad (2 required) |
|
| 133–62–1 |
|
8,000 lb. (3175 kg) Capacity Swing Air-Jack |
|
| 20–1184–1 |
|
Front-Mount Power Unit Bracket |
|
|
*Drive-Thru Kit cannot be used on L421 with Extension
**Standard equipment with Hunter wheel alignment systems
|
|
|
The Hunter L421 Lift has been certified under the program conducted by Automotive Lift Institute (ALI) and ETL Testing Laboratories, to comply with Safety Standard ANSI/ALI ALCTV-1998 and Electrical Standard ANSI/UL 201.
Because of continuing technological advancements, specifications, models and options are subject to change without notice.
NOTICE:
Product delivered to international markets may differ slightly in content to domestic product. Please consult your local distributor for details.
|
|
Ordering Information
|
|
|
